Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Enterprise, NV
Gate installation in Enterprise, NV means matching what the HOA architectural committee already approved, then building it to survive triple-digit Mojave summers and full afternoon sun. Most of this suburb went up between the 1990s and 2010s, so the gates here are ornamental wrought iron, steel drive gates and builder-grade aluminum pool barriers – not rural pipe gates. That changes the work. We install, repair and automate gate systems across Enterprise, and we do only gates. Call (844) 435-3018. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Enterprise Homes Are Different
Enterprise is a master-planned, HOA-heavy suburb on the southwest side of the Las Vegas Valley, and that single fact shapes nearly every gate job here. In communities like Southern Highlands and Mountain’s Edge, the architecture committee wants an exact iron-pattern match before anyone touches a street-facing gate. An off-the-shelf replacement that looks close usually gets rejected, and the homeowner ends up paying twice. We measure and photograph the existing gate before we quote so the new one clears review the first time.
The climate adds its own pressure. Very low humidity and intense UV fade and oxidize exposed iron faster than in milder parts of the country, and occasional monsoon dust and wind drive grit into hinges and operator tracks. Winter overnight freezes can crack cheap control boards on automated gates. On the desert-edge lots, gates facing west or south take the full afternoon sun, so solar operators and boards fail noticeably faster there than on shaded interior streets. Pool and backyard safety gates also have to satisfy Clark County pool-safety rules at the same time they satisfy HOA aesthetics. That double requirement is the real Enterprise gate problem, and it’s why general handymen struggle here.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Enterprise Services
Most Enterprise calls we take fall into two buckets: a gate that has stopped working, and a gate system that needs power and control work.
Gate Repair in Enterprise
Mechanical repair in Enterprise usually means iron gates that have rusted at the weld points, hinges that have worn oval, or a latch that no longer lines up because the post has shifted. The 1990s to 2010s tract housing here means a lot of original iron and builder-grade aluminum now showing its age. We diagnose the actual failure before quoting, then fix the hinge, weld, latch or panel rather than selling a whole new gate. For a closer look at what we handle, see Gate Repair in Enterprise. Estimates are free and the price is agreed before any work starts.
Electric Gate Repair in Enterprise
Automated gates in Enterprise take a beating from the sun. Control boards, photo-eyes and operator arms on south- and west-facing driveways fail faster than shaded ones, and dust from monsoon winds works into tracks and limit switches. We work on LiftMaster, FAAC, BFT and Linear systems among others, so we diagnose your operator rather than pushing a replacement brand. Safety edges and the power run get checked as part of the visit. Full detail lives on Electric Gate Repair in Enterprise.
Gate Installation in Enterprise
New gate installation in Enterprise is rarely a simple swap. The HOA sets the iron pattern, the county sets the pool-safety rules, and the desert sun sets how long the operator will last – so a gate installed here has to satisfy all three at once. Our technicians have up to 14 years of experience, and our Gate Installation work covers the whole job: measure, match, set posts to proper footing depth, hang the gate and wire the operator. Western and southern exposures across the desert-edge lots are the ones we plan around most, because that’s where solar operators and control boards cook.
Automatic Gate Installation
Signs you need it
You’re tired of getting out of the car every time, or you want a keypad and remote entry at a guard-gated or keypad entrance where the old manual latch no longer lines up.
What it costs in Enterprise
A typical automated setup in Enterprise runs about $2,800 to $6,500 depending on gate size, operator type and whether the power run already exists.
How we do it
We confirm the HOA-approved gate spec, run power and low-voltage to the operator location, mount the operator and safety edges, then test the full cycle and set the limits.
Driveway Gate Installation
Signs you need it
Your existing driveway gate has rusted through at the weld points or the iron pattern no longer matches what the community requires.
What it costs in Enterprise
Driveway gate installation in Enterprise typically falls between $1,900 and $5,200 for the gate and hardware, with automation quoted separately.
How we do it
We measure the opening, match or replicate the approved iron pattern, set the posts to proper footing depth, hang the gate and check swing, clearance and latch alignment.
What Gate Installation Costs in Enterprise
| Item | Typical range in Enterprise |
|---|---|
| Automatic gate installation | $2,800 – $6,500 |
| Driveway gate installation | $1,900 – $5,200 |
| Operator and safety-edge wiring | $450 – $1,200 |
Can you match the iron pattern my HOA already approved?
Yes. We measure and photograph the existing gate and match the approved pattern before ordering, so the new gate clears the architectural committee instead of getting rejected and rebuilt. Call (844) 435-3018 for a free measure and a written price.
Do you handle the power run and the safety edges on a new automated gate?
Yes. We run the power and low-voltage, install the safety edges and photo-eyes, and set the limits and force so the operator stops safely. Call (844) 435-3018 – estimates are free and quoted before work starts.
Brands We Service in Enterprise
We work on the operators and hardware homeowners here already own, including LiftMaster, FAAC, BFT and Linear. That’s why we can diagnose the actual fault instead of steering you toward a brand we prefer. We don’t stock parts – every job is measured and ordered for your gate, so turnaround depends on the part. See our brands for the full list.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Enterprise, NV
| Service | Typical range in Enterprise |
|---|---|
| Automatic gate installation | $2,800 – $6,500 |
| Driveway gate installation | $1,900 – $5,200 |
| Operator and safety-edge wiring | $450 – $1,200 |
| Gate repair | $150 – $450 |
| Hinge and latch repair | $120 – $300 |
| Iron gate weld repair | $175 – $500 |
| Electric gate repair | $200 – $650 |
| Control board replacement | $250 – $700 |
| Photo-eye and safety-edge repair | $150 – $400 |
| Operator replacement | $700 – $1,800 |
In Enterprise, price climbs when the gate is oversized, when the iron pattern has to be custom-fabricated to match the HOA spec, and when no power exists at the operator location yet. Every number above is an estimate – the written, upfront price sets the final cost, and you approve it before any work starts.
Neighborhoods We Serve in Enterprise
We cover gates across Enterprise, from the planned communities to the newer infill, with the same dispatch window across the whole suburb. Fast dispatch from 7am to 7pm, Sunday through Friday.
- Southern Highlands
- Mountain’s Edge
- The gated communities along the southwestern edge
- Newer infill streets off the main valley corridors
Service Area – Cities Near Enterprise
Enterprise sits in the southwest valley, and gate work here overlaps with the communities around it. We also handle gates in Spring Valley, NV, Paradise, NV, Henderson, NV and Las Vegas, NV. Same brand coverage, same upfront pricing, same HOA-aware approach across the area. Call (844) 435-3018 to check your address.
Serving Enterprise, NV – Our Local Coverage Area
We serve Enterprise and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Company in Enterprise
We dispatch fast across Enterprise, 7am-7pm, Sunday through Friday, and we’re closed on Saturday. A call outside dispatch hours is booked into the next opening. We answer the phone 24/7, so call (844) 435-3018 and we’ll get a technician to your gate.
Most replacement and new gates in Enterprise need HOA architectural approval, and most cities require a permit for structural changes, so ask your HOA and the Clark County building department. We measure and match the approved spec so your submittal clears review.
We cover all of Enterprise, including Southern Highlands, Mountain’s Edge and the gated communities along the southwestern edge, plus the nearby valley cities. If you’re unsure whether your street falls in our area, call (844) 435-3018 and we’ll confirm.
If your gate has stopped working, needs an operator replaced or needs a new gate that clears the HOA and the pool-safety rules, call (844) 435-3018 for a free estimate. We work on LiftMaster, FAAC, BFT and Linear systems and more, we do only gates, and every price is quoted and agreed before work starts.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 30-60 min.
- 4You approve before work beginsNothing starts until you say go.
What Enterprise Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Paige Quinn"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Shane Norris"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Brooke Parker